Product name:p20 s plastic mould steel
Thickness:1.2-600 mm
Width::1220-4200 mm
Length:5000-18000 mm
Notes:coil thickness ≤ 25 mm
[email protected]                   Contact Us


  Details:

P20S Tool Steel - West Yorkshire Steel - ISO 9001 Approved

West Yorkshire Steel are stockholders and suppliers of P20S steel round bar, flat bar and plate. P20+S is a high tensile alloy tool steel grade supplied in the hardened and tempered condition. With its higher sulphur content it offer better machinability than P20 plastic mould tool steel grade.

Plastic Mould Steel - Saaj Steels Corporation | Plastic ...

Plastic Mould Steel P20+S P20+S is a high tensile alloy tool steel grade supplied in the hardened and tempered condition. With its higher sulphur content it offer better machinability than P20 plastic mould tool steel grade.Heat the P20S component slowly, allow sufficient time for …

P20+S Steel - Kohli Iron & Steel Store

P20+S is a plastic mould tool steel,P20 with higher sulphur content(0.30-0.50),thus improves machinability.It is delivered in pre-hardened condition.It is a high strength steel.

P20S P20+S Tool Steel - Special steel china supplier-OTAI ...

Tool steel P20 + S is suitable for mold production, improve the machining performance is required. Typical applications include support and injection mould, mould holders and zinc die casting mould. P20S is a versatile plastic mold and the characteristics of high strength steel is applicable to many other applications, such as axis and wear a belt

P20+Ni Plastic Mould Steel | Tool Steel P20+Ni | Die Block ...

Virat Special Steels is the largest Supplier, Stockiest, Importer and Exporter of P20+Ni Plastic Mould Tool Steel in India, USA and Europe.

DIN 1.2312 / AISI P20+S plastic mould steel

The steel has good polishability, it can be cemented in the bath or in gas and also put on the hard-chrome. Applications : Cavitations molds, standard mould base, compression mould for SMC, blowing mould, Pet preform mold, plastic piping & plumbing injection molds.

High Speed Steel | Tool Steel | P20 Mold Steel | P20

P20 Mold Steel The steel is commonly used for plastic injection mold cavities and tooling and for die casting dies for zinc. P20 is typically sold in the pre-hardened condition at a …

AISI P20+Ni Tool Steel | AISI P20+Ni Mould Steel | Plastic ...

Virat Special Steels is the largest Supplier, Stockiest, Importer and Exporter of AISI P20+Ni Plastic Mould Tool Steel in USA, India and Europe.

About Us - Otai Special Steel

Otai supplies AISI P20, P20+S, NAK80 etc for pre-hardened pouring mold, mold of polishing glasses, mould of mirror surface. etc. Engineering Steel Otai steel supplies AISI …

P20 Tool Steel - Special steel china supplier-OTAI Special ...

ASTM P20 Steel is a good quality plastic tool steel, P20 steel belong to the high quality medium carbon,Pre-hardness(28~34HRc) plastic mould steel. It no need further heat treatment. so you don’t have any worry about distortion or cracking.

Plastic Mould Steel P20 Wholesale, Steel P20 Suppliers ...

Alibaba offers 95,646 plastic mould steel p20 products. About 98% of these are moulds, 1% are steel round bars, and 1% are steel sheets. A wide variety of plastic mould steel p20 options are available to you, such as container plate, boiler plate.

P20 Plastic Mould Steel|2311: Malaysia Carbon Steel Supplier

Description. P20 Tool Steel (40CrMnNiMo8-6-4) — P20 Plastic Mould, DIN 1.2311, 3CrMo Plastic mould steel that is usually supplied in a hardened and tempered condition. Good machinability, better polishability, compared to 1.2312 (AISI P20 S).

Plastic Mould Tool Steels - ssm.co.nz

P20+S. 1.2312. Chrome, Manganese, Molybdenum Steel with Sulphur, prehardened and tempered to 950 - 1100 Mpa. ... High performance plastic mould steel with good corrosion against chlorides. Good machinability and polishability. Good dimensional stability. Rounds. Diam 35mm -

P20 Tool Steel - West Yorkshire Steel - Only £25 UK ...

P20 tool steel is ideally suited for the production of plastic moulds. Typical applications include die holders, zinc die casting dies, backers, bolsters and injection moulds. The versatility of P20 tool steel with its high tensile characteristics enables uses for a variety of …

Plastic Mould Tool Steels - ssm.co.nz

P20+S. 1.2312. Chrome, Manganese, Molybdenum Steel with Sulphur, prehardened and tempered to 950 - 1100 Mpa. ... High performance plastic mould steel with good corrosion against chlorides. Good machinability and polishability. Good dimensional stability. Rounds. Diam 35mm -

P20 Tool Steel - West Yorkshire Steel - Only £25 UK ...

P20 tool steel is ideally suited for the production of plastic moulds. Typical applications include die holders, zinc die casting dies, backers, bolsters and injection moulds. The versatility of P20 tool steel with its high tensile characteristics enables uses for a variety of …

P20 tool steel chemical composition,mechanical, Physical ...

Mechanical Properties: Plastic mould steel that is usually supplied in a quenched and tempered condition. Good machinability, better polish ability, compared to 1.2312 (AISI P20+S).

P20 Tool Steel (40CrMnNiMo8-6-4) | Interlloy | Engineering ...

P20 is a plastic mould steel that is usually supplied in a hardened and tempered condition. Exhibiting good machinability with better polishability, compared to 1.2312 (AISI P20+S).

DIN 1.2312/AISI P20+S Plastic Mould steel, Steel Flat ...

Applications: plastic moulds, frames for plastic pressure dies, hydroforming tools (All technical information is for reference only) Pre: DIN 1.2311 Plastic Mould Steel, Steel Flat, Steel Round Bar

P20 mould steel - D2 steel|4130 steel|4140 steel|H13 steel ...

3,Features of P20 Plastic Mould steel . 1, Alloy tool steel which offers good machineability; 2, Excellent polished finish for large section; ... Large mould, such as fridge and air-conditioner. Packaging & Shipping . The container is usually 20 ft . Company Information .

Plastic Mold Steel - Tool Steel-High Speed Steel China ...

Plastic mold steel is a dedicated plastic products mold steel material, Commonly used steel grade P20, P20 S, P20 Ni, 1.2311,1.2312,s136, 718 Steel

P20 Steel - Hot Die Steel - Stavax ESR - C 45 Carbon Steel ...

P20 Steel,Hot Die Steel, Stavax ESR, C 45 Carbon Steel Plates, P20 High Hard Mould Steel, Suppliers in Delhi, Gururam, Manesar, Noida, Faridabad, India. Buy H13 Hot Die Steel and p20 plastic mould steel in good price. Our P20 Pre hardened steel available in 28 HRC to 48HRC. P20 Mold Steel a low-alloy steel, C45 steel

DIN 1.2311 / AISI P20 - ALTA Special Steel Co.,Ltd, Tool ...

Suitable for large or medium sized and precise plastic moulds. Tools for hot working such as inter-inserts and heat-stressed auxiliary tools. Cavitations Molds, Standard Mould Base, Compression Mould for SMC, blowing mould, Pet preform mold, plastic piping & plumbing injection molds.

P20 Steel Plate | 1.2311 | 3Cr2Mo | Plastic Mold Tool Steel

The special purpose mold steel P20 steel plate is commonly used for plastic injection mold cavities and tooling and for die casting dies for zinc. P20 mold steel plate material is typically sold in the pre-hardened condition at a hardness of approximately 300 HBW.

P20 Plastic Mould Steel (1.2311 DIN) at Rs 97 /kilogram ...

P. B. International - offering P20 Plastic Mould Steel (1.2311 DIN), Mould Steel at Rs 97 /kilogram in Mumbai, Maharashtra. Get best price and read about company and get contact details and address.

P20 Steel Equivalent, P20 Steel Equivalent Suppliers and ...

P20 Steel Equivalent, Wholesale Various High Quality P20 Steel Equivalent Products from Global P20 Steel Equivalent Suppliers and P20 Steel Equivalent Factory,Importer,Exporter at Alibaba.

Plastic Mould Steel 塑料模具钢 - Wong Tool Steel Sdn ...

Plastic mould steel, mould base, fixture, component etc Heat Treatment The increase the service life of mould up to 800,000 times, you may harden the pre-hardened steel by means of quenching and low-temperature tempering.

p20 plastic mould steel 400mm thickness - carbon …

we promise we can offer you the qualified p20 plastic mould steel 400mm thickness at the competitive price and rapid delivery time.We can produce as our customer's requirement.We keep many p20 plastic mould steel 400mm thickness stock in our warehouse, So hereby, we sincerely hope you join us, let's join hands to make you be the No.1 in your local steel market.


  Related Products :

brass self tapping screw

Din En 1 7220 34crmo4 Metal Alloy Steel Scm435

ophelia leather bars

automatic carbon steel shearing machine